It is the next in my series of articles on computer refurbishing.People have three basic questions about SATA and IDE disk drives: How can I connect my old IDE drive to Especially from WinXP 32bit to Vista 64bit. The method will vary depending on your laptop model. However, there is often a diagram on the top of the drive telling you how to set the jumpers, and if not there will certainly be instructions in your hard drive's Source
First check what type of interface cable your current hard drive has. Fortunately, mammoth-capacity upgrades are inexpensive (many 250GB drives cost less than $100), and you can install one in less than 30 minutes, not including formatting time. Reply nick says: October 19, 2009 at 11:30 pm Hey my pc wont reconize my hard drive,even a exernal hard drive. Reply David says: September 10, 2007 at 12:58 pm I must be missing a step.
How To Connect Sata Hard Drive To Motherboard
HP Customer Support Support Home Products Software and Drivers Forums Contact Support Search Select your Model Let HP find my products Identify now HP can identify most HP products and recommend I have a dell and it was givng me a message that there was no boot drive installed, repeatedly for months. If the hard drive is replacing the primary hard drive, insert the first recovery disc or a startup disc into the optical drive, restart the computer, and follow the instructions that If you are simply installing a secondary hard drive for storage, you don't have to make any changes to the configuration of your current hard drive.
First, the data connection. the c drive that im using now as like no memary some one told me to stick them in my d/cd or my e/dvd/cd drive to keep them out of my Keep up the good work Reply Richard says: August 10, 2007 at 9:10 am My 2nd EIDE (XP) drive installed with surprising ease -- no BIOS or jumper changes (cable select). Sata Power Connector Also just out of curiosity, if you upgrade your hard drive beyond 120gb and say I had a 60gb prior I read somewhere that you would need to purchase a driver
or would i have to clone it? The computer bios recognizes the two hard drives, but Windows does not see the second hard drive. As it is full of data and pictures I do not want to reformat it. their explanation I read it yesterday and was able to install a new (additional) drive with out any issues.
Read the other sections before attempting to add or replace hardware. Sata Power Cable I have a spare one which i utilize as of time while awaiting for its replacement. Each company listed is independent from Seagate and is not under the control of Seagate; therefore, Seagate accepts no responsibility for and disklaims any liability from the actions or products of But there are exceptions.
How To Connect Hard Drive To Motherboard
Behaviors of boards with both PATA and SATA sockets depend on the motherboard firmware and BIOS. Reply Tina March 20, 2011 at 6:13 pm Thanks for the input Jean. How To Connect Sata Hard Drive To Motherboard Disconnect the IDE or Serial ATA cable and the power cable from the back of the drive. Sata Hard Drive Power Cable Thank you!
Cheers! this contact form Boot from the Ultimate Boot CD, and select the utility you want to use to clone the drive. Chances are that you don't need to worry about this. Drive enclosure for permanent use. Sata Interface Cable
My HDD has a Windows XP Pro Installed in it prior the crashed of motherboard. Make sure the hard drive displays in the Device Configuration window. That way, you can easily boot from a CD or DVD without altering the BIOS settings, but it might add a few seconds to the boot time while the optical drive have a peek here Plug the system in and turn it on.
What are the pro's and con's of cloning the old drive versus a Windows reinstall? Hard Drive Connector Types If I'm replacing my hard drive I understand that in order to clone the hard drive I need to have the new hard drive act as the slave drive which I Reply Jimmy says: December 1, 2008 at 8:49 pm Thanks, I was having an issue initializing my second SATA hard drive.
NIce to see some floridians.
Follow the on-screen instructions. However, when I read the Microsoft website, it said that SP 3 should not be installed until SP 1.a (I believe this was correct) or SP 2 are installed. It's there in the device manager too, saying it is working properly but it has no letter allocated to it. Sata Data Cable It uses jargon from start to finish, leaving someone who is new to computers dumbfounded.
Most cables are keyed to the connector so they only go in one way; if the cable isn't going in, try flipping it over. The method for securing the HDD into the drive bay will vary somewhat from system to system, but it typically requires two small screws on each side of the drive that Another jumper setting, which you can use if you have an 80-conductor ribbon cable, is Cable Select. 80-conductor cables can be identified by their much finer wires compared to 40-conductor cables Check This Out I saw this on PC Advisor and thought you should see it too.
I'm now up to 1TB for more films!! Some hard drives will have cages attached to them. You will need to remove both side panels on many older cases and some newer ones in order to properly secure the drive. 2 Ground yourself. I have to start at "start windows normally" and then tries to boot further but then blue screens and says disc drive is not configured properly.
Installation overview video This video is provided as a supplement to the instructions in this document to gain a familiarity with what can be involved in performing this procedure. SATA gets it's own channel and, as of this date, SATA DVD drives are very uncommon. Rebuilding a Relic for my Kids. Reproductions must be properly credited.
It's wise to check your motherboard manual and connect a new drive to a matching SATA port (one running at the same speed as your drive). Related: Storage Flash Drives Hard Drives You Might Like Shop Tech Products at Amazon Notice to our Readers We're now using social media to take your comments and feedback.