i have 2 sata drives and 1 ide drive.runing windows xpi'm having problems with my ide drive.my system iswindows xp proffessional1 gig memorysata drive 1 160 gigsata drive 2 300 gigide You shouldn't have any problems using the converted drive as a slave. However, you'll sometimes see transition drives. Most motherboards have only PATA or SATA data connector sockets. check over here
To launch the BIOS, you have to press a special key before the computer boots into Windows. Plugged in the new 160gb Western Digital SATA hard drive and installed a fresh copy of Windows 7. Reply Www.diolt.com February 28, 2011 at 10:27 am Hello thanks for the nice information you shared Reply FreeReferrals February 27, 2011 at 9:40 pm Thanks this was very helpful and I they dont need jumpers..
Motherboard With Ide And Sata Ports
Just use the power plug you have, no worries. If you find out any good info, please let me know...thanx!Regards,Robert Flag Permalink This was helpful (0) Collapse - Sata is primary by edersch / July 28, 2005 9:26 AM PDT Login now.
I simply can't get into bios when I remove the jumper. If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). Hope this helped. How To Make Ide Boot Instead Of Sata There was a pop up box saying to close the program or restart the program, however, I clicked on the close the program.
It wasn't after checking this thread! Use Ide Drive With Sata Motherboard I just bought a new DELL Dimension E310. I've had this setup running on my machine for the last 2 years (approx) and haven't had any problems.Windows manages the two hard drives separatly so you shouldn't have any problems.I Thanks.
How To Connect Ide Hard Drive To Sata Motherboard
IDE optical drive with sata HDD Tom's Hardware Around the World Tom's Hardware Around the World Denmark Norway Finland Russia France Turkey Germany UK Italy USA Subscribe to Tom's Hardware Search http://www.techspot.com/community/topics/cant-run-a-sata-hdd-and-a-ide-hdd-together.111412/ IDE AND SATA DRIVES AND HOW THEY WORK TOGETHER solved Can't use ide-to-sata adapted drive to boot from? Motherboard With Ide And Sata Ports IDE, on the other hand has jumper settings that mandate boot order, so that could be what's causing your problem. Ide And Sata Drives In Same Computer I tried exactly what you did all to no avail.
Well I figured out my own problem! check my blog The IDE HD had to be on the secondary IDE cable in order for it to be recognized by the sata drive. Can I run IDE Drives and SATA Drives Together? We also taught you all about partitions How To Set Up A Second Hard Drive In Windows: Partitioning How To Set Up A Second Hard Drive In Windows: Partitioning Read More Ide Hard Drive Jumper Settings
Should I just remove the jumper from the IDE one? As you can see, some drives have helpful diagrams just above the jumper pins. Svchost.exe using a ton of memory usb ports No sounds windows 10 Strange horizontal spikes/lines on... this content Then you connect its special power plug that powers both the connector and drive.
My OS is on my SATA hard drive and when I plug in my EIDE maxtor 160 GB HD the system trys to boot from it. How Many Hard Drives Can Be Connected To A Single Ide Cable I had 4 devices working through 2 EIDE ports including my WD hard drive and then a Seagate HD through primary on SATA. How much degradation you experience depends on the patterns of your disk use and which IDE standards are involved. (I exclude these complexities here.) For typical office work this configuration works
The hdd shows up in the device manager, but n Using IDE optical drive and SATA HDD?
The OS now loads from the SATA HD and the EIDE HD was assigned a new drive letter on it's own and everything is functional. Reply Vignesh May 28, 2016 at 6:29 am Connect the old hard drives in other computers. Set The Jumpers & Plug In Since I only have a single IDE CD-ROM and single hard disk to show you today (as well as only a single physical IDE connector What Are The Two Goals When Implementing A Raid Solution Plugged the 160gb Western Digital IDE hard drive with all my stuff on it back in and I don't see it?...
The one below has a SATA data cable connector plug, combined with both kinds of power plug connectors. The SATA power connector is depicted in the following image. By continuing to browse our site you agree to our use of data and cookies.Tell me more | Cookie Preferences Partially Powered By Products Found At Lampwrights.com make-use-of-logo logo-background menu have a peek at these guys Ive gone a head and done this but im having issues.
There was a place where I could select boot order (HDD, CD/DVD, Floppy, etc.) but no place to specify the boot order of the individual hard drives. PlayStation Vue: How Do… 5 Privacy Protecting Apps You Need to Use Right Now Internet Security 5 Privacy Protecting Apps You Need to Use Right Now Advertisement Related Articles 3 Free Flag Permalink This was helpful (0) Collapse - Same problem here... IDE and SATA drives use different controllers.
Hi, Your new drive would be the faster drive. I don't see an option for autodetecting hardware in my BIOS, by MSI. Am I even looking at the correct location in bios? 08-16-2011, 12:46 AM #10 GZ Retired Join Date: Jan 2010 Location: New Jersey Posts: 25,552 OS: Windows PlayStation Vue: How Do… 5 Privacy Protecting Apps You Need to Use Right Now Internet Security 5 Privacy Protecting Apps You Need to Use Right Now Advertisement Related Articles 3 Free
Sure enough, the BIOS shows two devices loaded and functional. It sould work like a charm :) And yes, there is no way to change a sata drive master/slave. 0 zap44 10 Years Ago This post helped me greatly.