Home > Hard Drive > Cannot Install Windows On WD 500GB SATA Hard Drive

Cannot Install Windows On WD 500GB SATA Hard Drive

Contents

Once the installation is complete and you have installed Service Pack 2, enable UDMA again. I have bought a recovery CD but this does not work either. Using Write Signature & Upgrade Wizard: Click Next on the first screen, and then select the drive you wish to install (in this case Disk 1). Get the answer shahidloneMar 24, 2013, 6:08 AM connect the hdd to other computer if detected then format it.after that connect to your laptop. weblink

But VIA Technologies has a web site dedicated to VIA hardware support. I tried different connecters and different sata ports in my MB. MS does not recognize the CD I created: XP for SATA as authentical. popo says: October 10, 2008 at 8:55 am THANKS!!!,UR tutor was damm cool,i used Nlite and cant believe how coll the stuff is.I appreciat :man!

Western Digital Sata Hard Drive Jumper Settings

If not, maybe try a BIOS update. Adding Second Drive: Click the Start button and then access Control Panel -> Administrative Tools -> Computer Management -> Storage -> Disk Management. I haven't done this in a while, and so I was surprised that I could pick up a Western Digital 250 GB SATA II drive for only 69 bucks - with

Thanks! MB: Asus P7H55-M PRO Chip: Intel i5 650 3.2 GHz RAM: 4GB DDR3 (2x2GB) Kingston HD: WD Caviar Blue SATA, 500 GB Thanks in advance, alguy Dec 4, 2010 #1 Geoff says: August 1, 2008 at 5:24 am Excellent Guide, Everything made sense in your tutorial, but I can't figure out how to determine which SATA drivers my Clevo M570U needs. Toshiba 2.5 Sata Hard Drive Jumper Settings If the drive had data on it that you want to try and recover, we recommend NOT trying to partition or reformat the drive, as this data can be lost forever.

I downloaded another freeware utility called nLite, which allows you to configure a Windows XP installation image with whatever drivers you want, as well as provides some other really cool features. Jumper Setting On Hard Disk All Rights Reserved. Thanks again! http://support.wdc.com/knowledgebase/answer.aspx?ID=981 Have you tried a different power connector?

If you have an OEM computer you may not have any options in the BIOS to change that. Toshiba Hard Drive Jumper Settings I'm not sure what the problem is but I do recommend asking your question on our forums so other techs can address the problem. If it does not verify the connections are secure. I popped the new drive into a spare bay, plugged in the SATA cable and the power connector, and booted up the Windows XP installation CD.

Jumper Setting On Hard Disk

Last Hitachi one was apparently faulty (which it only told me some way into Windows setup 😦 I have just bought an ExcelStor Jupiter Sata II but when I detach the this content nfo_id=932 and request it by providing some personal information over the phone. Western Digital Sata Hard Drive Jumper Settings Start Windows XP and allow the Operating System to boot to the desktop. Wd10ezex Sata Jumper Settings However, you will need a floppy drive for that.

Hmmm, I guess I thought too soon; SATA drives are apparently not supported by the Windows XP installer. have a peek at these guys Report • #13 matvangogh February 8, 2014 at 07:42:06 its a intel ich8r/ich9r/ich10r/do sata raid controller keep in mind when i got this PC it was from the Dell outlet and Make sure that your system BIOS is properly configured. Once your drive has been partitioned and format verify it appears under My Computer. Seagate Ide Hard Drive Jumper Settings

If this doesn't work, you can try going to the manufacturer's website and get the breakdown of Sectors, Cylinders, etc and manually input the figures. Disabling fast boot in the BIOS may allow additional time. I turned LAN off on bios and re-run and just came up this time operating system not found the bios doesn't find the HD could this be the cable causing this check over here First, you need to access the site from the machine you want to probe - this is understandable.

Enter the BIOS and set the drive to IDE, NOT RAID. Western Digital Hard Drive Installation Software I am linking to Security essentials below. XP explorer and device manager show SATA hard drive I installed but it doesn't show up in BIOS.

Good luck.

I put my laptop hard drive Seagate ST950042 0AS 500 gb (it stopped working) into external enclouser and plug into my other laptop throughr USB. This can be installed once Windows 2000 is loaded on the drive. March 16, 2012 DuROi Thanks for your fast reply, i already update my bios to the lastest one (BIOS Update - R0104J0) successfully. Function Of Jumper Pins In Hard Disk In my experience, though, partition problems should not cause the drive to not be detected in BIOS.

Is this likely to be a PSU error as sometimes they work just fine? RAID can be used on IDE, SATA, SCSI or other types of hard drives. If you already have XP installed on your SATA drive - done while configured as an IDE drive - then you have two potential problems: 1) The SATA drivers that come this content Left-click on Finish when done.