Home > Hard Drive > Extra IDE Slot

Extra IDE Slot

Contents

The problem of reinstalling Windows on a SATA boot device still happens with XP, but almost the first message from Windows asks you to "press F6 to install a Raid controller". All submitted content is subject to our Terms of Use. The standard does not distinguish this value. All of the additional wires in the new cable are ground wires, interleaved with the previously defined wires to reduce the effects of capacitive coupling between neighboring signal wires, reducing crosstalk. useful reference

The other drive or Slave drive was for data storage. The case screws are bigger than the ones used to screw in your CD drives. DirecTV Now vs. ATAPI was adopted as part of ATA in INCITS 317-1998, AT Attachment with Packet Interface Extension (ATA/ATAPI-4).[14][15][16] UDMA and ATA-4[edit] See also: UDMA The ATA/ATAPI-4 standard also introduced several "Ultra DMA" http://www.techspot.com/community/topics/extra-ide-slot.967/

Ide Hard Drive Jumper Settings

Flag Permalink This was helpful (1) Collapse - New computers often handle this well by jrfree / July 22, 2005 6:42 AM PDT In reply to: Mixing SATA and IDE drives The operation is slow. Write out a quick table to figure out how it is currently set up, like this: CHANNEL 1, MASTER: CHANNEL 1, SLAVE: CHANNEL 2, MASTER: CHANNEL 2, SLAVE: Probably your hard The ATA connector specification does not include pins for supplying power to a CF device, so power is inserted into the connector from a separate source.

Multiplied by 512 bytes per sector, this totals 528482304 bytes which, divided by 1048576 bytes per megabyte, equals 504 megabytes. Operations on the devices must be serialized—​​with only one operation in progress at a time—​​with respect to the ATA host interface. If the User password is not available, the only remaining way to get at least the bare hardware back to a usable state is to issue the SECURITY ERASE PREPARE command, What Is The Voltage Of The Red And Yellow Wires On Most Power Supplies? This permitted the established block protocol to be reused in storage area network (SAN) applications.

Inside your computer, you generally have two (2) IDE hard drive controller connections. How To Connect Ide Hard Drive To Sata Motherboard Had to buy a "new" hard drive from Hunter Engineering, and Frankenstein some old parts together. Just use the power plug you have, no worries. What is this?

This allows commands to be sent to the other device on the cable, reducing the impact of the "one operation at a time" limit. How To Connect Ide Hard Drive To Motherboard A Cable Select cable can be used with master/slave drive jumpering. You can see where the IDE data ribbon cable plugs in to connect it to the motherboard and where the Molex power plug goes. These photos show the SATA data cable sockets on the motherboard, the red SATA data cable and its end plugs, and the black SATA power plug -- SATA Photos (Wikipedia)             The

How To Connect Ide Hard Drive To Sata Motherboard

by R. Homepage Flag Permalink This was helpful (0) Collapse - Ahh, that never seems to work. Ide Hard Drive Jumper Settings Parallel ATA cables have a maximum allowable length of only 18in (457mm).[2][3] Because of this limit, the technology normally appears as an internal computer storage interface. How Many Hard Drives Can Be Connected To A Single Ide Cable Reply James Bruce November 18, 2015 at 8:16 pm if you only have 1 IDE channel on your motherboard, then you're out of luck.

Flag Permalink This was helpful (0) Collapse - mixing of sata and ide by Ranjan_Ind001 / July 22, 2006 9:23 PM PDT In reply to: Mixing SATA and IDE drives in Depending upon your bios and startup options, if it is like mine you have the option either within the bios, or at startup, which drive to choose as the primary. Stevens; Paul J. Proffitt Forum moderator / December 10, 2006 3:26 AM PST In reply to: SATA HDD + IDE drives w/ SATA adapters Burying a new discussion here is not going to find Ide Cable Select

Install hard drive Before you install the new drive make sure you unplug the power connector from the computer. However, some flash memory drives can use pin 20 as VCC_in to power the drive without requiring a special power cable; this feature can only be used if the equipment supports On each channel, you could add up to 2 IDE devices – so that meant a maximum of 4 hard drives and/or CD-ROM drives. Ask a new question Read More Homebuilt Connection Cable Components Systems Product Related Resources Two ide hdd`s- into 1x ide port 1x sata port on mobo. 2 drives, 1 AHCI only,

There are two things to keep in mind, do not overload your power supply or strange difficult problems will begin to occur and make the correct BIOS settings for your data Ide Cable Definition Most boards have 2 channels while 4 is becoming more and more common at least on the higher end boards. The less expensive solution was the addition of a dedicated CD-ROM interface, which was typically included as an expansion option on a sound card.

This is true whether or not you use the Master/Slave style or the Cable Select style.

OSNews Forgot Password · Register Login to OSNews Username or EmailPassword Search OSNews Advanced Search Submit News RSS Home Originals News Archive Shopping Topics FAQs Contact Advertise How to Integrate SATA First, Master and Slave devices are different for the 80-wire cables and the 40-wire cables. Look on the bottom right and you'll see something that looks like this picture. How To Install Ide Hard Drive Discussion topics include SSD, SATA drives, USB drives, external hard drives, RAID arrays, backup, IDE drives, network attached storage (NAS), thumbdrives, Western Digital, Kingston, LaCie, and SanDisk.Real-Time ActivityMy Tracked DiscussionsFAQsPoliciesModerators General

I'm using an Asus P4P800-VM mobo and it requires an advanced (not for beginners says the user guide) BIOS setting to use both serial-ata and parallel-ata devices. Before you start Do not drop or bump the drive. Cable Select jumpering requires a special IDE cable with wire 28 not connected to one of the drive connectors, which would configure the drive attached to that connector as the slave Thank you for helping us maintain CNET's great community.

Sata is primary drive and it was automatically set to drive H. do you have enough, reserve capapcity for another card, drive (and fan, if temps are close to boardline)? Visit »www.promise.com/Products ··· ADAPTERS Regards,Doctor Olds · actions · 2001-Sep-21 1:40 am · Funner567Scrappy-Lan-join:2001-03-16Beverly Hills, CA

Funner567 to shaka Member 2001-Sep-21 1:43 am to shakahow much do they cost? Your mobo sounds similiar to mine.

In addition, no ATA hard drives existed in 2005 that were capable of measured sustained transfer rates of above 80MB/s.